Learn how to make jewelry with holiday sublimation earring designs!
Who loves a good seasonal accessory? I do! With my collection of new sublimation earring designs, you can create all sorts of beautiful seasonal projects! These sublimated earrings are fantastic for beginners as well as more experienced sublimation crafters. So, are you ready to make a pair of your own?
Earrings are one of the easiest sublimation projects, they add the perfect amount of flair to any outfit, and it’s easy to make multiples at a time for wearing, gifting, or selling. You can even mix and match designs for a custom set!
However, you can’t sublimate just any regular earring base — they need to be special sublimation earring blanks. What makes them special?
The sublimation blanks in my materials list are made from MDF, just like the ornaments we used in my Sublimation Christmas Ornaments tutorial. MDF stands for “medium density fiberboard,” and is an alternative to wood. But that’s not what makes them special — it’s the white polymer coating that does, because it can be sublimated!
Since the MDF earring blanks and the ornament blanks are so similar, you can follow the steps in the sublimation ornaments tutorial to sublimate your own pair of earrings.
Since I absolutely love seasonal accessories, I made fifteen new PNG patterns to share with you! These designs will keep you bejeweled with cute seasonal earrings from fall through winter. There are autumn designs like leaves, adorable ghosts, bats, and pumpkins, as well as cute winter designs that carry through Christmas. The floral gingerbread people design might be my favorite!
You can use these sublimation earring designs to make other projects besides earrings, too. Just resize them to fit your blank and follow the tutorial for a successful sublimation result.
To sublimate the earrings in my materials list, you’ll need some basic sublimation materials, like white cardstock, uncoated white butcher paper, and heat-resistant tape. You’ll also need a heat source — in this case, a heat press. I used my Cricut Autopress, but you can also use a Cricut EasyPress, Mini Press, or another heat press to sublimate your earrings. Just make sure it can reach 375°F.
Once your earrings are sublimated, you can attach the earring hooks using two pairs of pliers and the steps below:
- To make the earrings hang correctly, hold the hook firmly between two fingers, then grip the entire earring loop between the pliers and twist your wrist 90 degrees. Repeat with the second earring hook.
-
Using two pairs of pliers, grip each side of the separate jump ring. Rotate one wrist forwards or backwards, so the jump ring creates an opening but doesn’t bend out of its circular shape.
-
Slide the hole of one earring onto the jump ring.
-
Slide the earring hook onto the jump ring. Pay attention to which side is the front of the earring to be sure the earring and hook are both facing the right direction.
-
Use two pairs of pliers to grip each side of the jump ring. Twist your wrist in the opposite direction to close the jump ring again. If it doesn’t close completely, open the jump ring and try again until the two ends of the jump ring meet.
Let me show you how easy it is to make jewelry with my holiday sublimation earring designs! This post contains some affiliate links for your convenience (which means if you make a purchase after clicking a link I will earn a small commission but it won’t cost you a penny more)! Read my full disclosure policy.
Materials to Make Sublimation Earring Designs
-
- Sublimation Earring Blanks
- Sublimation Printer or Printer Converted for Sublimation -AND-
- Sublimation Ink
- (Optional) Your ICC Printer Profiles (here are the Hiipoo printer profiles)
- 8.5″ x 11″ A-Sub Sublimation Paper
- Heat Press – I used the Cricut Autopress but you can use the Cricut EasyPress or Cricut Mini Press
- Google account – to use Docs for photo editing
- White Cardstock (for sublimation)
- White Butcher Paper (for sublimation)
- Scissors
- Heat Resistant Tape
- Cricut Trimmer
- Brayer
- Lint Roller
- Fan (for ventilation)
- Two pairs of Flat Nose Pliers (for attaching the earring hooks)
-
- Design #643 (My free PNG design files are available in my free resource library – get the password by filling out the form at the bottom of this page)
How to Use Holiday Sublimation Earring Designs
Find the directions below for the MDF ornaments and apply these steps to your earring blanks. Then, see my instructions above to add the earring wires!
DIY Sublimation Ornaments
Make your own sublimation ornaments with printed designs or Infusible Ink!
Materials
- Here is a shopping list of the actual items I used to create this project! This list contains affiliate links. As an Amazon Associate I earn from qualifying purchases.
- Sublimation Ornament Blanks Small -OR-
- Sublimation Ornament Blanks Large -OR-
- Snowflake Sublimation Ornament Blanks for photo designs
- Sublimation Paper - I used 8.5" x 11" A-SUB Sublimation Paper
- Sublimation ink for your printer - I used Hiipoo ink
- Infusible Ink Transfer Sheets and the butcher paper that comes with them
- Ceramic Ornament Blanks - for Infusible Ink
- Protective Paper - I used 12" x 12" 65 lb Cardstock
- White Butcher Paper
Tools
- Sublimation Printer - I used my Epson EcoTank ET-4760
- Heat Press - I used the Cricut Autopress
- Laptop or Desktop running Windows or Mac
- Google account - to use Docs for photo editing
- (Optional) Your ICC Printer Profiles here are the Hiipoo printer profiles
- Heat Resistant Tape
- Lint Roller
- Ventilation - I use this fan
- Cricut StandardGrip Green Mat, 12" x 12"
- Scissors
- Weeding Tool - helpful for Infusible Ink
Instructions
STEP 1: GET OR PREPARE A SUBLIMATION DESIGN
First, download my sublimation ornament designs from this page — or search the library for design number 410. I've included a folder of sublimation designs sized for two sizes of ornaments as well as a folder of designs to make with Infusible Ink.
Today, I'll show you how to sublimate the Sweater Weather design on a large ornament. You can use the same steps for the other designs, too, or use your own image. Then, I'll show you how to make an Infusible Ink ornament.
STEP 2: PREPARE FOR SUBLIMATION
Once you’ve picked a design, you’ll need to print it on a good quality sublimation paper for the best results. I’m using A-SUB paper in my Epson EcoTank with Hiipoo ink. You can, of course, do this on another sublimation printer with different sublimation ink, too! Make sure you use compatible supplies.
There are lots of ways to print your design but I’ll show you my favorite method: Google Docs!
On your desktop computer, go to Google Docs in the Google Chrome web browser. You can also download and open the Google Docs app on a phone or tablet, BUT be aware that you won't be able to install or access any printer profiles from a mobile device.
If you don’t have a Google account, they’re free and easy to get.
First, click on "Blank" to open a new document.
In the top File menu, select Page Setup. Change your margins to 0. Change your Paper Size to match your sublimation paper size. I’m using letter size. Click OK.
Now click on the Insert menu at the top and select "Image," then select "Upload from Computer." Locate the sublimation design you want to use in the folder you downloaded from my library. I’ll use the "sweater weather" file. Then click "Open." The image will appear on your page!
But, it won’t necessarily come in at the correct dimensions for our ornaments. One of the neat things about sublimation is that you can let the design cover the entire object you're decorating. That's especially helpful for irregularly-shaped items. Measure the shapes as if they're rectangles and we'll adjust the file to fit.
The large rectangular ornaments are 4.3" x 2.83" so I need to make the design 5.1" wide. I need to print it a bit larger to account for the orientation marks, but Google Docs makes that easy!
If you're using a different ornament, measure the width and height to adjust the files accordingly.
Click the image, select "Image Options," then "Size and Rotation." Keep the "Lock aspect ratio" box checked and change the width in the correct field.
I’ll enter "5.1" for the width to include the orientation lines. The image is automatically resized! The colorful area is just a bit larger than my actual ornament width.
Next, let’s make sure the design will print in the right spot. To reposition the image, select it and then click on "Wrap text" from the menu that appears below. You might have to hover your cursor at the bottom of the image to bring up the menu.
Now, you can click and drag the image anywhere on your page. I recommend putting your design in the center of your page, as that ensures it won't get cut off at the edges. Once you're more experienced with your printer and sublimation, you can put more designs on a page to save paper.
Once you’re happy with the design, give it a name by clicking where you see “Untitled” in the top left field. Another great thing about Google Docs is the auto-saving feature! No more losing your work if you forget to save every few minutes!
STEP 3: PRINT YOUR SUBLIMATION DESIGN
Before we print, make sure your paper is loaded correctly. Check your printer manual and paper packaging for help identifying the right side to print on and how to load it. If you’re using A-SUB paper in an Eco Tank like me, place the paper facedown with the words “A-SUB” visible so that the design will print on the bright white side of the sublimation paper.
While printer settings vary, the main things we have to watch for are paper type and print quality. The process is different for each printer so check your manual.
Here are my processes for my Epson Eco Tank and Sawgrass, both of which are popular sublimation printers.
Epson Print Method
If you have an Epson, go to the File menu and choose Print.
Select your printer under "Destination." Then, click the arrow beside "More Settings" and click "Print Using System Dialog."
Make sure your sublimation printer is selected under "Printer". Then, under "Layout" click "Flip horizontally" to mirror your image. Most sublimation projects need to be mirrored, so remember that step!
Choose "Print Settings" and change your media type to "Presentation Paper Matte" and Print Quality to "High Quality."
We already mirrored the image, so don’t click that. And don’t use high speed!
If you’ve installed an ICC printer profile for better colors, which I covered in my sublimation printer setup videos, you can select that here as well. Select "Color Matching" and choose your printer profile. If you’re on a Mac as I am, choose "Color Sync," click on the menu, select "Other Profiles," and select your printer profile from the list.
Once you’ve correctly adjusted your settings for your printer, click on "Presets" and choose "Save Current Settings as a Preset" and then you can choose that from now on!
Sawgrass Print Method
To print on a Sawgrass, go to the File menu, choose "Print," and select your printer under Destination. Then, click the arrow beside More Settings and click "Print Using System Dialog."
This is where the steps for the different printers change. Click the PDF menu in the lower left corner and choose Sawgrass Print Manager. If you’re having an issue finding this, look for your Print Options and select Sawgrass Print Manager as your printer. This is the only way to access the helpful ICC printer profiles that Sawgrass provides.
Your window might look different, but choose your settings that match your ornament. For mine, I’ll set the substrate – that means what we’re sublimating on to – to “MDF” and paper to “Type A”. Again, I recommend Quality over Speed! Sawgrass automatically knows we want to mirror the design, so don’t uncheck that box by accident.
Then, look at the preview to the right and make sure your design looks correct. If not, hit Cancel and make any adjustments you need until you’re happy.
Finally, click the pink Print button and watch the magic happen!
STEP 4: PREPARE FOR SUBLIMATION
There are many variables in sublimation - heat, pressure, ink, substrate, etc. - so you might have to do some experiments to find your perfect combination. Consult your press manual for reference, too, but you can use my settings as general guidelines.
Let your heat press warm up to 375°F while you prepare to heat the ornament. I'm using a Cricut Autopress, but you can use an EasyPress, or other heat source that reaches 375°F.
Since sublimation produces fumes, open a window or turn on a gentle fan to dissipate any vapors in your working area.
Some ornament blanks have a protective clear sheet on them. If yours does, remove it from one or both sides.
Then, use a lint roller to remove any debris from the ornament.
Once your press reaches the target temperature, place the ornament face up on the pressing area and put a piece of butcher paper on top. Do not use parchment paper, wax paper, freezer paper or teflon paper - these will trap moisture. Preheat the ornament for 10 seconds just in case there is any moisture present.
While the ornament cools a bit, place your printed design on your work surface with the ink facing up. Make sure the design is mirrored and will look right once it's transferred to the ornament.
Place your ornament face down on the printed design, using the alignment marks to line up the center.
TIP: To make sure your ornament covers most of the design, carefully hold it up to a light to see the alignment better.
STEP 5: PRESS YOUR SUBLIMATION DESIGN
Lay a piece of white cardstock larger than your design over the press mat to catch any excess ink. Tape the ornament to the image using heat resistant tape. Place your ornament on the cardstock with the taped image on top.
Place a piece of white butcher paper on top of the ornament and design.
Set the Autopress or your machine's timer for 60 seconds and press the project. The Autopress will open right at 60 seconds. If you’re using a different machine, lift the press straight up to avoid shifting the design and causing blurs.
The sublimation process is still active for 10-15 seconds after the heat has been removed. You can remove the butcher paper, but leave the ornament in place to cool.
When you are confident that your print has transferred, you may remove the tape and paper.
Add a ribbon or hook through the loop and your ornament is ready to display or give as a gift!
Variation: Photo Ornament
Since you can use any image you own for sublimation ornaments, you can also decorate one with your own photo or design.
When selecting a photo for small sublimation projects, there are a few things to keep in mind. First, make sure the subject will be recognizable if you make it small enough to fit on the blank. Second, make sure it's high quality enough to look nice printed out.
Making a photo ornament in Google Docs follows most of the same steps as working with my PNG design file. I'll show you how to put one on the round ornament in the materials list. They have round inserts that are 1.125" or 1.625" in diameter that we can sublimate on. I'll show you how on the larger one.
Follow the same steps to prepare your Google Doc setting and add the photo you want to use. The image will appear on your page, but probably not at the right size or shape.
Printed sublimation projects don't have to be the perfect size for the item you're decorating. But you also don't want to print a huge image when you'll only use a few inches for your project.
With the image selected, click the icon in the top menu that looks like a square with some extra lines. This will open the Crop tool. Move your cursor to a black rectangle at an edge of the image until it turns into an arrow.
Then click and drag that line closer to the subject you want to put on the ornament. Repeat for the other three sides. Click the Crop icon again to commit to the change. Now you'll avoid printing a lot of excess photo!
Right-click the image, select Image Options, then Size and Rotation. Make sure the image is just a bit larger than the ornament. If it needs to be smaller, keep the "Lock aspect ratio" box checked and change the width in the correct field.
Follow the earlier directions for your printer.
After your image has printed, place it face up on your work surface. You can trim it to be closer to the ornament's disc size, though, to make it easier to manipulate.
Remove the protective film from the round insert, then place it face down on the print right over the subject. Add heat resistant tape to the edges to keep it perfectly in place. Cover your pressing area with fresh white cardstock and place the ornament with the image on top. Cover it with fresh butcher paper and press it at 375°F for 60 seconds.
While the image cools, peel the white sticker off of the ornament to reveal the adhesive area. Make sure the ornament's hanger is at the top and carefully press the disc in place with the right orientation.
INFUSIBLE INK
If you don't have a sublimation printer, you can make similar ornaments with Infusible Ink using my files in the second download folder. You can download the free SVG cut files from my free resource library, it's Design #410. Then, upload the design collection to Design Space.
If you are not sure how to upload an SVG cut file to Cricut Design Space, watch this helpful video training series I made.
If you are on an iPad or iPhone, here is how to download and upload SVG files to the Cricut Design Space app.
Here is what the Infusible Ink ornament collection looks like on my Canvas.
You can zoom out to see all of the designs by clicking on the minus (-) sign on the lower left.
With the designs selected, click "UnGroup" so you can work with each ornament independently.
If there are ornaments you don't want to make, select them and click "Delete" above the Layers Panel.
Or, if there is an ornament you want to make you want to make more of, select it and click "Duplicate."
Next, make sure the designs are the right size for your ornaments by clicking each in the Layers Panel to see its dimensions. My ornaments are about 3" so these will fit well. We're ready to cut.
Make sure the right machine is selected and then click "Make It."
If prompted, select "On Mat" and "12 in x 12 in" then click Continue.
On the Prepare screen, click the "Mirror" toggle below all your mats. Then click Continue.
Select "Infusible Ink Transfer Sheets" for your material and set the pressure to "More". Make sure your clean Fine-Point Blade is in Clamp B. Then click Continue.
Place your first Infusible Ink sheet shiny side down on StandardGrip mat.
Load your mat and press your machine's Go button.
Once the mat is finished, unload it, flip it over on your workspace, and gently roll a corner back to release the Infusible Ink.
Complete the process for the rest of the mats.
NOTE: I recommend you wash and dry your hands immediately before handling Infusible Ink to avoid transferring any oils to the surface.
Trim your excess Infusible Ink and then cut the designs apart.
To weed Infusible Ink Transfer Sheets, use the “cracking” method. Slightly bend and roll the cut paper until you hear a little cracking sound (which happens as the cuts separate). Don’t worry if your design lifts off the liner a bit. After you “crack” your cut design, just take away the excess paper and you’ll be left with just your design on the liner.
Next, prepare your heat press. Use the Cricut Heat app or Cricut Heat Guide to find the right settings for your blank and transfer material. Since I'm using my Autopress and ceramic ornaments, I'll press at 400°F for 200 seconds.
Next, we need to position each design over an ornament and secure it with heat resistant tape. Make sure you place the design matte side down on the shiny side of the ornament. This is why we mirrored our designs!
Place your Cricut Pressing Mat on the platen and cover it with white cardstock larger than your ornament.
Then, place your ornaments on the cardstock, design down. Cover them all with a piece of white butcher paper
Heat according to your instructions.
When they're done heating, let the ornaments cool down before moving them. Moving them right away could cause ghosting of the image since the sublimation process does not end immediately,
After they have cooled, you are free to remove the tape and reveal the sublimated designs.
Add ribbon or hooks to hang them!
STEP 6: SHOW THEM OFF!
Take care of your ornaments by storing them carefully wrapped in paper towels.
Notes
Typefaces: Andala, Divine Light Hand and Market Street from FontBundles.net
Answers to Your Questions About Making Sublimated Earrings
Q: What are sublimation designs?
A: Sublimation designs are images (usually PNG files) that are printed with a sublimation printer using sublimation ink. The printed images are then infused into the blank using high heat via heat press to a (most often) white, polymer-coated or polyester surface.
Q: How long do you heat press sublimation earrings?
A: I pressed the MDF sublimation earrings from my materials list at for 60 seconds at 375°F.
Q: Can you heat sublimation too long?
A: Yes, it is possible to apply too much or too long of heat to your sublimation transfer. Often items that were sublimated too long or at too high of heat will have a brownish cast to them, or sometimes the ink can even fade from the blank.
Q: What materials can you not sublimate on?
A: Without some extra preparation, you should not try to sublimate items that are not white or light colored, as well as items that are not coated by a polymer or made from polyester. Because sublimation ink is sheer, sublimation transfers aren’t as visible on darker materials. Sublimation ink also cannot be infused into materials that do not have a polymer coating or materials that are made from at least 60% polyester. You CAN sublimate materials like 100% cotton, but the design will fade away completely the first time it is washed unless you take some extra steps to prepare the surface.
Q: Is sublimation better than vinyl?
A: This is a very subjective question! Depending on your budget and your desired outcome, and other factors, you may decide that heat-transfer vinyl is a better option for you than sublimation, or vice versa. Do your research before investing in a slew of new craft supplies and equipment, and try out lower cost options (like Infusible Ink transfer sheets rather than purchasing a sublimation printer at first) before deciding if sublimation is right for you.
Q: Do you let sublimation cool before peeling?
A: Different projects have different answers to this question, but most sublimation projects should be cool to the touch before removing the heat-resistant tape and transfer to reveal the design.
Q: Can a Cricut do sublimation printing?
A: While a Cricut cutting machine can be useful in some sublimation projects, it does not sublimate or print sublimation ink. However, you can use a Cricut and Infusible Ink pens to draw designs onto paper which can be sublimated, or use a Cricut to cut SVG designs out of Infusible Ink transfer sheets.
Q: Why can’t you sublimate white?
A: There is no white sublimation ink, so when your printer prints a sublimation design including white, it simply does not add ink to those areas. Instead, to include white in your sublimation design, you need to be sure to sublimate onto a white surface. Sublimation ink is translucent, meaning the color behind it will show through. This is why you shouldn’t sublimate directly onto darker colors — it won’t show up correctly without extra work.
Q: Can you print your own sublimation designs?
A: You sure can! To print your own sublimation designs, you’ll need a sublimation printer, sublimation ink, and sublimation transfer paper. You can get links to all of these in my materials list!
Q: Can you use Canva for sublimation?
A: Canva is one of my favorite tools for sublimation. Not only are there thousands of images and designs available to use for your sublimation projects, but you can design your own images in Canva as well. To learn more, check out my Canva Creative Workshop!
Get my free PNG files to make your own holiday sublimation earring designs!
(If you do not see the signup form above, click here.)
I love seeing what you make with my designs and how you use them! Inspire others and share a photo of your sublimated holiday earrings and other projects in our Facebook group or tag me on social media with #jennifermaker.
Love,